Selkirk Bird Proof Round Top, Aluminum, Galvalume, Dimensions: 6 in Dia These tops cannot be used for wood burning applications Helps prevent rain and debris from entering the vent External screen prevents entry of most bird species

Selkirk Storm Collar, Vent Hole Size: 6 in, Material Gauge: 28 ga, Steel, Galvanized, Dimensions: 9-5/8 in OD x 1-9/16 in L, Installation Type: Wall, Suitable for: Type B Gas Vent Use above the flashing Seal inner edge with hi-temp silicone sealant Use to...

Selkirk Roof Flashing, Pipe Size: 6 in, Aluminum/Galvanized Steel, 18 in OAL, 15-1/4 in OAW UV-resistant polypropylene Built in water deflectors Cold impact-resistant to -40 deg

Selkirk Shielding Insulation, Universal, Dimensions: 2 in THK x 48 in L x 12 in W, Suitable for: Chimney System, Support Box, Attic Insulation Shield and Insulated Wall Thimble The SUSI protects building materials against radiant heat from the chimney and helps maintain temperatures...

This new design gives you the flexibility of securing the 5, 6, 7 or 8 in Dia chimney with a heavy-duty band. The band allows you to slide the installed length verticaly to properly position this section in the system. Installation requirements are the...

Selkirk Flashing Kit, Pipe Size: 5 to 8 in, Rubber, Includes: 23-4/5 x 21-1/2 in Rubber Boot, Mounting Screws, Spacers Kit, Special Storm Collar

Fits all roof pitches and requires only simple framing. Brackets and mounting hardware only. Fits all roof pitches and requires only simple framing Mounts easily on to top of roof through opening that allows two inch clearance

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, two-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal pressure venting only....

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal pressure venting only....

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, two-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal pressure venting only....

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal pressure venting only....

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal pressure venting only....

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal pressure venting only....

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, two-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal pressure venting only....

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal pressure venting only....

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal pressure venting only....

Used to start chimneys indoors or outdoors using a wall support assembly or a masonry pier. A length of insulated chimney pipe is attached to the tee snout, using a Locking Band, to pass safely through combustible walls. An insulated tee cap is included...

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal pressure venting only....

Can be used for fixed offsets of 15 deg slope or in pairs for offsets adjustable from zero to 30 deg slope. Greater angles are prohibited by UL standard 103 and by the terms of the product listing. Required locking bands (2 packaged with...

Can be used for fixed offsets of 30 deg slope. Greater angles are prohibited by UL Standard 103 and by the terms of the product listing. Required Locking bands (2 packaged with each elbow kit) are to be used at each joint. Each offset...

Selkirk Drip less Smoke Stove Pipe Adapter, Stainless Steel, Dimensions: 15-3/4 in L, Suitable for: Single-Wall Stove Pipe and Sure-Temp Type HT Chimney Pipe, Includes: Coupler For use in new installations, this part can be installed by twist-locking the coupler on-the DSAC into the...

Selkirk Drip less Smoke Stove Pipe Adapter, 316 Stainless Steel, Dimensions: 15-3/4 In L For use in retrofit installations, this part can be installed from below to a MCS finish ceiling support and secured with screws

Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy-gauge steel construction for long life. Retains chimney with a twist-lock connection. The Anchor Plate provides a secure attachment for the...

Contains one 18 in L of pipe, roof brackets and necessary hardware. Not for use with coal burning stoves. Fits all roof pitches and requires only simple framing Mounts easily on to top of roof through opening that allows 2 in clearance

The support box is intended for use when installing chimney in an A-frame, in a mobile home or in a ceiling under a narrow section of roof. It provides a finished installation at the ceiling level and will support up to 20 ft of...

The Type HT wall support kit has been tested for use fully enclosed and has been designed in 5 in, 6 in, 7 in and 8 in sizes to carry up to 60 ft of height at 2 in from wall. The capacity of...

Interior resupport assembly allows for two different methods of chimney resupport. The first method is used at the immediate section of chimney above the upper elbow of an offset. With the appropriate fire stop/joist shield (JS) in place, clamp the support band around chimney...

Used whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load and to prevent damage from static and sliding snow. It should be used, at a midpoint on-the...

Prevents or delays the rapid spread of fire (regardless of the cause) in a home or building. The sheet metal firestop prevents the chimney passageway from becoming an easy pathway for fire to spread from one floor to another.

Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA smoke pipe adapter to lower end of chimney or to insulated tee.

Used to trim the ceiling when a chimney is supported from above and extended down into room. Also used in conjunction with firestop/joist shield.

Used wherever a ceiling support, finish support, firestop or joist shield is installed below an open attic. Required to guard against the hazard of blown-in or blanket insulation filling any framed opening or contacting the chimney and possible storage of combustibles against the chimney....

Provides a finished appearance where the chimney passes through a sloped ceiling. Matte black finish. Adjusts to multiple roof pitches. Covers 4 in space around chimney pipe (or 2 in further than the required clearance). Pitched ceiling plate provides a finished appearance where the...

Used along the wall to provide for 2 in clearance and assure stability. Useful for suspending offsets. Required at 8 ft or closer intervals to stabilize the chimney, wherever it is supported along a vertical wall. The Wall Band is used along the wall...

The Pitched Ceiling Support Kit provides all necessary parts for a complete installation with the exception of the required insulated pipe lengths and adjustable flashing (AF). Selection of the Adjustable Flashing is determined by the pitch of your roof.

For a wall-supported chimney system with a horizontal connector passing through an exterior wall, connecting to a Tee and running verticaly up the exterior wall to termination above the roof line. The thru-the-wall support kit provides all necessary parts for a complete installation with...

Diamond shaped 1/2 in x 1 in mesh, 18-8 stainless steel. Fits same size round chimney top. Keeps foreign objects out of chimney.

Part of the chimney system roof assembly, the round top is designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft. in the Sure-Temp-Type HT Chimney (5 in, 6 in, 7 in and 8...

Designed to fit on-the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after...

Flashings are used to seal the opening where the chimney penetrates the roof and to divert rain and snow down from the roof and away from the chimney system. A Series of adjustable flashings are available depending on your roof pitch. A flat and...

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal pressure venting only....

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal pressure venting only....

Used to start chimneys indoors or outdoors using a wall support assembly or a masonry pier. A length of insulated chimney pipe is attached to the Tee snout, using a locking band, to pass safely through combustible walls. An insulated tee cap is included...

Selkirk Drip less Smoke Stove Pipe Adapter, 430 Stainless Steel, Dimensions: 15-3/4 In L For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of MCS chimney

The Type HT wall support kit has been tested for use fully enclosed and has been designed in 5, 6, 7 and 8 in sizes to carry up to 60 ft of height at 2 in from wall. The capacity of the larger sizes,...

Used whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load and to prevent damage from static and sliding snow. It should be used, at a midpoint on...

Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee.

Provides a finished appearance where the chimney passes through a sloped ceiling. Matte black finish. Adjusts to multiple roof pitches. Covers 4 in space around chimney pipe (or 2 in further than the required clearance). Pitched ceiling plate provides a finished appearance where the...

Used along the wall to provide for 2 in clearance and assure stability. Useful for suspending offsets. Required at 8 ft or closer intervals to stabilize the chimney, wherever it is supported along a vertical wall. The Wall Band is used along the wall...

Flashings are used to seal the opening where the chimney penetrates the roof and to divert rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and...